Opens in a new tab
(208) 680-6446

How Often Should Commercial Concrete Be Sealed in Utah?

If you manage a commercial property in Utah, your concrete takes a beating every winter. Sidewalks, entries, plazas, loading areas and parking decks all deal with water, ice, plows and de-icing salt for months at a time.

Sealing is one of the cheapest ways to protect that concrete. The question we hear most from facility managers is simple: how often does it need to be done? Here is the straight answer, why the number changes from one surface to the next, and how to check your own concrete so you are not guessing.

Why Utah is hard on concrete

Concrete looks solid, but it is porous. Water soaks into it, and what happens to that water next is where the damage starts.

Freeze-thaw cycles

Utah winters swing above and below freezing over and over, sometimes in the same day. Water that has soaked into unsealed concrete freezes, expands, thaws and soaks in a little deeper. Repeat that all winter and the surface starts to flake and pop off. That is spalling, and once it starts it tends to spread.

Road salt and mag chloride

De-icers keep walkways safe, but they are rough on concrete. Salt and magnesium chloride brine get carried into the pores with the meltwater, and they speed up the surface breakdown that freeze-thaw starts. Entries, drive lanes and parking structures that get treated all winter usually show it first.

Not all de-icers are equal. Industry guidance from concrete associations notes that magnesium chloride and several other de-icers cause much higher rates of deterioration than plain sodium or calcium chloride. The same guidance says to keep de-icers off new concrete entirely during its first year.

A good penetrating sealer keeps most of that water and brine from soaking in. Concrete associations point to silane and siloxane penetrating sealers as the strongest defense against de-icer and freeze-thaw damage. They do not last forever, though, which is why the resealing schedule matters.

How often to reseal: the short answer

For most commercial concrete, plan on resealing every 3 to 4 years. Where your concrete falls in that range depends on how it has been treated since it was poured: whether it was sealed at all, how consistently it has been maintained, and how much traffic and de-icer it sees.

Concrete that has been maintained: every 3 to 4 years

If your concrete was sealed and has been kept up, a reseal every 3 to 4 years is the typical schedule. Higher-traffic and heavily salted areas lean toward the shorter end.

Concrete that is already spalling or damaged: more coats up front

If the surface is already flaking, pitting or showing other damage, one coat usually is not enough to start. It may need more than one coat at first to get it protected, and then a maintenance coat every 2 to 3 years after that. Damaged concrete absorbs more, so it uses up its protection faster.

New concrete: about once every 5 years

New concrete that gets sealed and stays on a schedule may only need sealing about once every 5 years. Starting early is the best way to keep it in that range. Manufacturer data sheets generally call for concrete to cure for about 14 to 28 days before a penetrating sealer goes on, depending on the product, so the first coat fits right after construction and before the first winter.

Why sealer life varies

You will see sealer life quoted anywhere from a few years to more than a decade. Both can be true. How long a sealer lasts comes down to four things: the type of sealer, the warranty behind it, the condition of the concrete it went on, and whether the surface is a wall or something people walk and drive on.

The type of sealer

Penetrating sealers, usually silanes and siloxanes, soak into the concrete and react inside the pores. They leave no film on top, so the surface still breathes and keeps its natural look. Film-forming sealers, like acrylics, sit on the surface. They can add color or a sheen, but traffic wears them off sooner.

The manufacturers’ own numbers show the gap. Prosoco’s published service-life estimates for its penetrating water repellents for concrete paving run 10 to 15 years, while its acrylic and enhancing sealers are listed at 3 to 5 years. Those are best-case figures for properly applied product. Plows, traffic and a winter of salt are why real-world reseal schedules on Utah flatwork run shorter.

The warranty behind it

Read the warranty, not just the label. The standard data-sheet warranties from both Sika and Prosoco cover defects in the product itself, not how long it will keep water out. Longer coverage is something you qualify for. Prosoco, for example, offers extended 5- and 10-year warranties when a RILEM tube test on the treated surface passes its water-absorption limit.

Evonik, maker of the Protectosil silane and siloxane line, offers long-term, field-verified warranties that must be set up with its regional manager before work starts. Qualifying projects using Protectosil CHEM-TRETE BSM 350 or BSM 400 can carry up to a 20-year labor and material warranty. We can apply Protectosil products when a project specs them. A long warranty is a guarantee on qualifying work, not a reseal schedule.

New construction or a worn surface

Sealer applied to new, sound concrete has the best chance of reaching the long end of its life. Concrete that is already worn, scaled or spalling absorbs more and has weak spots where water gets in, so it uses up its protection faster. Penetrating sealers also cannot bridge real cracks or open joints, so those need repair first.

Vertical or horizontal

This is the biggest difference of all. Walls, columns and other vertical surfaces get weather but no wear and tear. Nobody walks on them, plows do not scrape them and salt brine does not sit on them. Horizontal surfaces with heavy foot or vehicle traffic get far more exposure, and they wear out sooner. In our experience, high-traffic concrete needs resealing every 3 to 4 years, while sealer on vertical surfaces lasts 5 to 10 years, depending on the substrate.

Surface Traffic Typical reseal range
Vertical walls, columns, precast None 5 to 10 years, depending on the substrate. The longest of any surface
New horizontal concrete, sealed early Light to moderate About every 5 years
Maintained sidewalks, plazas, entries Foot traffic Every 3 to 4 years
Drive lanes, parking decks, salted entries Heavy foot or vehicle The short end of 3 to 4 years, so test every year
Worn, scaled or spalling concrete Any Multiple coats to start, then every 2 to 3 years

Manufacturer warranties are a separate question from these reseal ranges. The longest ones, such as the 20-year labor and material warranty available on qualifying Protectosil projects, depend on the product, the project and approval before work starts.

How to tell if your sealer is still working

Schedules are a starting point. The better way to decide is to test the concrete itself. There are two simple ways to do it.

The water splash test

Splash some water on the concrete and watch what it does. If the water beads up and sits on top, the sealer is still working. If the concrete darkens as the water soaks in, the sealer has worn off in that spot and it is time to reseal.

Test a few areas, not just one. Main entries and drive lanes usually wear out first.

The RILEM tube test

For a more measured answer, we use a RILEM tube test. A small graduated tube is sealed to the surface with putty and filled with water, and we read how much water the concrete has absorbed after 20 minutes. It works on walls and flatwork, and it gives you a number to compare before and after sealing, or from one year to the next. We run our own RILEM tests for assessments. When a manufacturer warranty is involved, though, the manufacturer’s sales rep has to perform and verify the test, so we schedule that with them.

What a resealing job looks like

Sealer only works if it can soak into clean, dry, sound concrete, so prep matters as much as the sealer itself. We normally use sealers from Sika or Prosoco, can apply Evonik Protectosil products when a project specs them, and pick the product for the surface: a penetrating repellent made for traffic and de-icing salt on flatwork, and one suited to the material on walls. A typical commercial job goes like this:

  • Assess the surface and test how it absorbs water
  • Clean the concrete so dirt, oil, curing compounds and old sealer do not block penetration
  • Let it dry. Manufacturers note that excess moisture keeps sealer from penetrating and shortens its life
  • Repair cracks and damaged areas, and prep very porous spots as needed
  • Treat a test area first, as both manufacturers direct
  • Apply the sealer evenly by sprayer or roller
  • Keep traffic off until it is ready, then set the next reseal date

We will tell you up front how long each area needs to stay closed so you can plan around tenants, deliveries and parking.

When to seal

Sealing can be done any time of year, but winter is best avoided because freeze-thaw cycles have already started. The warmer months and fall are the best time to seal, so the concrete goes into winter protected.

Frequently asked questions

How often should commercial concrete be sealed in Utah?

Most commercial concrete needs resealing every 3 to 4 years. Concrete that is already damaged may need extra coats at first and then a maintenance coat every 2 to 3 years. New concrete may only need sealing about once every 5 years.

How can I tell if my concrete needs to be resealed?

Splash water on it. If the water beads up, the sealer is still working. If the concrete darkens, the sealer has worn off. A RILEM tube test gives a more precise reading of how much water the concrete absorbs.

Do walls need resealing as often as sidewalks?

No. Vertical surfaces get weather but no foot traffic, plows or standing salt brine, so a sealer lasts much longer there. In our experience, sealer on walls lasts 5 to 10 years depending on the substrate, compared with 3 to 4 years on high-traffic concrete. Long manufacturer warranties on qualifying projects are a separate guarantee.

Does salt really damage concrete?

Yes. Road salt and mag chloride get carried into the concrete with meltwater and speed up the flaking and surface breakdown that freeze-thaw causes. Magnesium chloride is among the harder de-icers on concrete. A penetrating sealer helps keep that brine out.

Get a quote

Not sure where your concrete stands? We can test it and give you a straight answer on whether it needs sealing now or can wait.

Call us at (208) 680-6446 or request a quote and we will set up a time to look at your property. We work across Salt Lake, Utah, Davis, Weber and Cache counties, plus Park City and Heber.

Related posts

Leave the first comment